Search results

Looking for a way to convert over to a newer style master cylinder and booster. I have already installed a disc brake conversion kit on the front wheels. What I need to know is if their is a newer style master cylinder (dual chamber with an equilizer) system that is available that would bolt on...

I have 401 and 364 nailhead engines. Will any parts interchange with these two engines? Was wondering mainly about the push rods and rocker assemblys?

Where can I purchase a new sending unit for my 57 Buick? Has a 364 V-8. Have been to several parts stores and many web searches with no luck...

Have an engine that was pulled out of a 57 buick but do not think it was correct engine for that car. Looked it up on this site and I think it is a 401 but not sure. The engine numbers are, 4G40121 13. Can anyone help me out?

I also posted this in shop talk forum...Have had a lot of frustration in trying to get my dynaflow transmission rebuilt. I"m to the point that I feel it is time to get moving with my project so could use some advice on doing a conversion to my vehicle. I have a 1957 Buick Special with a 364...

For almost two years I have tried to get someone to rebuild my dynaflow, something always comes up, don't have time, don't do them anymore or the cost of an overhaul is so expensive, (and the shop is so far away), I would have to sell my house to get it done. I have been thinking about putting...

Does anyone know of a place where a person could get a 57 Buick automatic transmission rebuilt? Looking to have it done right. I'm located in the mid-west so may work out better if it was not to far away from where I live, within 150 to 200 miles.... Any help would be appreciated.

Will be putting my drive train back in soon and was wondering if there are any special things to look for when installing? My transmission has been setting in the shop for about two and one half years, should I replace the front and rear seals before installation? Any other seals that should be...

I have a 57 that is equiped with power steering. Of course the power steering system is in need of a complete rebuild. I was thinking about installing a manual steering gear box (also 57 special), in place of the power steering gear box. Looks like it would be an easy change out. Is there...

I need a new carb for my 364 nailhead. Changed out the manifold from a 2 barrel to a 4 barrel. Do not have a 4 barrel carb core, just looking for a carb to rebuild or purchase one that is ready to put on. Have looked everywhere, so far only Kanter has one that will fit and I found one on Ebay...

Is there any special things a person should need to know about rebuilding the heads on a 364? This engine is in a 57 buick and was wondering if I should update heads to use unleaded gas? I was told by someone that it is not a good idea to put in hard valve seats as this usually causes problems...

Have been shopping around for a new or rebuilt carburetor for my 57 Buick. So far have found only one place that has what I need. I do not have a core because I'm changing from a 2Brl to a 4 Brl set up. There seems to be several choices to pick from. Can anyone tell me what would be a better...

Does anyone have information on converting a 57 buicks front drum brakes to disc brakes? I also want to update the master cylinder. Are there any kits out there? :clonk:

I have not been a member of this site for a long time but do enjoy looking things over and asking questions about my 57. Started a frame off rebuild on a 1957 buick special, two door hardtop about two years ago. Well, you know how it goes. Seems I always run out of time or money. Sometimes both...

I need some help finding a new windshield for my restoration project. Did find one through PPG but was real exspensive. Looking for an installatoion kit also, Any suggestions?:shield:

I have a 1957 buick two door hardtop that I'm in the process of rebuilding. Have talked to several individuals about using the origanal buick transmission. Several people tell me that the buick transmission was plauged with problems and breakdowns. How dependable are these transmissions? I was...